Adept Python Manuale Utente Pagina 90
- Pagina / 170
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 5 - Module System Descriptions
90 Adept Python Modules User’s Guide, Rev. E
5.5 Mounting Options
When a Python module system is configured, mounting feet or toe clamps can be
included. Mounting feet are aluminum plates that bolt to the underside of module 1 and
allow the fully-assembled system to be bolted in place. Toe clamps are inserted into the
T-slots on the sides of module 1 and secured to the mounting surface. Each toe clamp kit
contains four toe clamps and two mounting screws per toe clamp. The type and number
of mounting feet or toe clamps are automatically configured based on the selected stroke
length for module 1.
The two digits following the system orientation characters define both mounting feet/toe
clamps and the quantity of feet/toe clamps required. In the example from Figure 5-1 on
page 68, “13” indicates an L18 module configured with three mounting feet. The
following chart shows all the available mounting options and the descriptor numbers
used to indicate them.
Figure 5-27. Mounting Options in Module System Descriptor Number
NOTE: If a gantry support module is included in the system, and if
mounting feet or toe clamps are configured on module 1, the same
number of gantry mounting feet/toe clamps are automatically included.
If no mounting feet/toe clamps are specified on module 1, no mounting
feet/toe clamps are configured on the gantry.
00
MOUNTING OPTIONS
L18 Mount Feet Kits, Quantity 2
00
12
13
21
15
22
23
25
33
32
No Mounting Hardware Supplied
L18 Mount Feet Kits, Quantity 3
L18 Mount Feet Kits, Quantity 5
L12 Mount Feet Kits, Quantity 1
L12 Mount Feet Kits, Quantity 2
L12 Mount Feet Kits, Quantity 3
L12 Mount Feet Kits, Quantity 5
L08 Mount Feet Kits, Quantity 2
L08 Mount Feet Kits, Quantity 3
81
1 Toe Clamp Kit, Quantity 4 Toe Clamps
82 2 Toe Clamp Kits, Quantity 8 Toe Clamps
83 3 Toe Clamp Kits, Quantity 12 Toe Clamps
- Adept Python 1
- Table of Contents 5
- List of Figures 11
- Introduction 1 15
- L18 Module with 16
- MotionBlox-10 Amp 16
- L12 Module with 16
- Product Description 17
- Special and Custom Orders 18
- Adept SmartController CX 18
- 1.4 How Can I Get Help? 21
- 1.5 Related Manuals 22
- Safety 2 23
- 2.3 Risk Assessment 25
- Avoidance 26
- Maximum Thrust 27
- Safety Barriers 28
- 2.5 Equipment Modifications 30
- 2.6 Transport 31
- 2.8 Sound Emissions 32
- 2.9 Thermal Hazard 32
- 2.10 Working Areas 32
- Python Linear Module 37
- Descriptions 3 37
- L-Series Module Types 38
- Payloads and Moments 38
- Stroke Length 41
- Accuracy 41
- Acceleration 43
- Resolution and Repeatability 43
- 143.50 mm 45
- 168.50 mm 45
- 295.50 mm 46
- Motor Mount Configuration 47
- Linear Module Options 49
- Harness Exit Configurations 50
- Module Preparation (Assembly) 51
- L18 030 S10 B0 M10 0 P0 0 0 52
- L18 030 S10 B0 53
- M10 0 P0 0 0 54
- L08 010 S10 B0 57
- LG6 020 P0 0 0 59
- Python Theta Module 61
- Description 4 61
- Gear Ratio 63
- Interface 63
- ± 360° RANGE OF MOTION 64
- (CONTINUOUS TURN AVAILABLE) 64
- LT1 G30 B0 64
- Module System Descriptions 5 67
- 10 S 1 0 0 0 69
- A0 A0 A0 A0 X00 0 70
- S 2 0 0 0 72
- Single-Axis Configurations 73
- Z-Axis motion 74
- Single-Axis Theta Modules 75
- 5.4 System Orientation 86
- Single-Axis Orientations 87
- Typical Two-Axis Orientations 87
- Module 1, Flipped 89
- Module 2, Rolled 89
- (Amp 2 facing Amp 1) 89
- 5.5 Mounting Options 90
- Mounting Feet Drawings 91
- Toe Clamp Drawings 92
- All dimensions 93
- CABLE 4 KIT - No cable 97
- CABLE 1 KIT - No cable 97
- 5.7 Gantry Mounting Kits 98
- GANTRY MOUNTING 99
- Dimension determined 100
- Y module 100
- LG6 Gantry Support Module 100
- 5.8 IO Blox 103
- IO BLOX OPTIONS 104
- CABLING/PLUMBING 107
- Module Installation 6 109
- Mounting Plate 110
- General Installation Notes 110
- Cleanroom System Installation 115
- Space Around the Chassis 117
- 7.2 System Cable Diagram 118
- 7.3 Installing the PDU3 119
- Power Distribution Unit 8 121
- 8.2 Installing the PDU3 122
- 200–240V~ 123
- 380–415V~ 123
- 8.5 PDU3 Fuses 125
- 8.6 PDU3 Mounting Brackets 126
- 8.7 PDU3 Dimensions 127
- Note: All dimensions 128
- 8.9 PDU3 Specifications 129
- XDCS Connector 131
- XSLV1/2 Connector 131
- Adept MB-10 Amps 9 133
- 9.2 MB-10 Operation 134
- Indicator LED 135
- Brake Release Button 135
- MB-10 Connectors 135
- IO Blox Connector 136
- 9.3 MB-10 Firmware 137
- 9.4 MB-10 Specifications 138
- Motor Connector 139
- Encoder Connector 139
- System Operation 10 143
- Power Checks 144
- Cable Installation Checks 144
- 10.3 Turning On Power 145
- 10.4 Software Configuration 145
- Load and Run DC_SETUP.V2 146
- 10.5 Enable High Power 150
- 10.6 Run-Time Calibration 151
- 10.7 Turning Off Power 151
- Maintenance 11 153
- 11.2 Checking Safety Systems 154
- Battery Replacement Procedure 155
- Retaining clip 156
- Replacement 158
- 11.6 Additional Maintenance 159
- 11.7 MB-10 Decommissioning 159
- Advanced System 161
- Configurations 12 161
- Robot #1 Robot #2 162
- User-Supplied 163
- 24VDC Power 163
- Terminator 164
- Installed 164
- 5960 Inglewood Drive 170
- Pleasanton, CA 94588 170
- 925·245·3400 170
Prodotti e manuali riguardandi Apparecchiature Adept Python
AEG S74100DTX0 manuály
Uživatelské manuály a uživatelské příručky pro Ledničky s mrazničkou AEG S74100DTX0.
Poskytujeme 1 manuály pdf AEG S74100DTX0 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Aeg S74100DTX0 Uživatelský manuál (20 strany)
Značka: Aeg | Kategorie: Fridge-freezers | Velikost: 1.84 MB |
Tabulka s obsahem
Další produkty a příručky pro Ledničky s mrazničkou AEG
| Modely | Typ Dokumentu |
|---|---|
| S2673KA6 |
Uživatelský manuál
Aeg S2673KA6 User Manual,
20 stránky
|
| RCB83726MX |
Uživatelský manuál
 
Aeg RCB83726MX Manual do usuário [da] ,
32 stránky
|
| 3640-6KG |
Uživatelský manuál
Aeg 3640-6KG Manual de usuario [da] [en] [es] [pt] ,
40 stránky
|
| SCE81826TC |
Uživatelský manuál
 
Aeg SCE81826TC User Manual [pl] [ro] [sk] [sk] ,
60 stránky
|
| S83800CTM0 |
Uživatelský manuál
Aeg S83800CTM0 Manuale utente [ru] ,
76 stránky
|
| S73400CNS0 |
Uživatelský manuál
Aeg S73400CNS0 User Manual [ro] [sk] ,
24 stránky
|
| SCE81824TS |
Uživatelský manuál
Aeg SCE81824TS User Manual [fr] ,
20 stránky
|
| OEKOS.S2583-BLU |
Uživatelský manuál
Aeg OEKOS.S2583-BLU Manual do usuário,
12 stránky
|
| A2174GS6 |
Uživatelský manuál
Aeg A2174GS6 Manual do usuário,
32 stránky
|
| S83930CTX2 |
Uživatelský manuál
Aeg S83930CTX2 Manual de usuario [pl] [ro] [sk] [sk] ,
16 stránky
|
| SCT71900S0 |
Uživatelský manuál
Aeg SCT71900S0 Manuale utente,
56 stránky
|
| SCE81831FS |
Uživatelský manuál
Aeg SCE81831FS Handleiding [en] ,
80 stránky
|
| SCE8182XTS |
Uživatelský manuál
Aeg SCE8182XTS User Manual [en] ,
20 stránky
|
| AGN71800S1 |
Uživatelský manuál
Aeg AGN71800S1 Manuel utilisateur [nl] ,
60 stránky
|
| AIK3023R |
Uživatelský manuál
Aeg AIK3023R User Manual,
24 stránky
|
| SCE81826TF |
Uživatelský manuál
Aeg SCE81826TF Manual do usuário,
40 stránky
|
| AGN71200F0 |
Uživatelský manuál
Aeg AGN71200F0 User Manual,
76 stránky
|
| A75238GA |
Uživatelský manuál
Aeg A75238GA User Manual [pl] ,
36 stránky
|
| ABB67211AS |
Uživatelský manuál
Aeg ABB67211AS Benutzerhandbuch [de] [en] ,
20 stránky
|
| AHB82621LW |
Uživatelský manuál
Aeg AHB82621LW Εγχειρίδιο χρήστη [de] [en] [fr] [it] ,
52 stránky
|
© 2020, manymanuals.it. Tutti i diritti riservati | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale